![]() In high-traffic or high-speed situations, you may need to increase the maximum queue size to avoid dropped messages. The word maxqueuesize, followed by an integer, sets the maximum number of incoming messages that can be in the queue at any given time (default="2048)." The work queue will grow as needed until this maximum limit is reached. Host destinations can be specified either by name (e.g., localhost) or by IP address (e.g., 127.0.0.1). The word host, followed by a symbol, specifies the host destination to which messages will be sent. The FullPacket message toggles support for the 'FullPacket' message used by the CNMAT Open Sound Control externals or the Max udpreceive object-when set, the udpsend object will send UDP buffers in the form of OSC 'FullPacket' messages. The udpsend object and its counterpart the udpreceive object provide support for third-party Max objects that work with the Open Sound Control (OSC) protocol developed by the Center for New Music and Audio Technologies (CNMAT) at the University of California, Berkeley. Sends the given message over the network using UDP. Sends a list message over the network using UDP. Sends a float message over the network using UDP. Sends an int message over the network using UDP. The source code for these versions is slightly different, while the Glade user interface files are significantly different between Gtk+ 2 and Gtk+ 3.Sends the bang message over the network using UDP. Compiled on a 64-bit machine with Gtk+ 3.Compiled on a 32-bit machine with Gtk+ 2, and.Tarballs for versions 4.0 and later, contain two sets of binaries: ![]() Releases (gzipped tarballs containing binaries and source): Hop-by-hop Destination Routing Authentication ESP TCP (IPv4) ICMP (IPv4) UDP (IPv4) TCP (IPv6) ICMP (IPv6) UDP (IPv6) 6to4 Send Host/IP ASN/IP Traceroute Load/Save PRNG TCP (IPv4) ICMP (IPv4) UDP (IPv4) TCP (IPv6) ICMP (IPv6) UDP (IPv6) They can be used to determine if the contents of a file are valid UTF-8, or to raise or lower the case of the UTF-8 characters in a file. They are not part of SPS and can be deleted if desired. In /src?/utils/ sub-directory, three UTF-8 utility programs are provided. Retrieve MAC address and current MTU setting of any attached network interface.ĭomain name resolution and reverse resolution. IP and ASN delegation functions, including: country name/code search and reverse-search, autonomous system (AS) number search by country and reverse-search, IPv4 and IPv6 address delegation search and reverse-search.ĪRP (IPv4) and Neighbor Discovery (IPv6) for querying a LAN for MAC addresses of local nodes. ![]() View packets in hexadecimal/ASCII representation, in both unfragmented and fragmented forms.Īll packet settings can be saved to and loaded from file. IP addresses and port numbers can be randomized.Ī configurable traceroute function, which supports TCP, ICMP, and UDP packets with all the features mentioned above. Assumed maximum transmission unit (MTU) can be changed if unusual fragment sizes are needed. Packet fragmentation for IPv4, IPv6, and 6to4. For those without access to a native IPv6 network, IPv6 packets can be transmitted over IPv4 (6to4). IPv6 support includes: hop-by-hop, "first" and "last" destination, routing, authentication, and encapsulating security payload (ESP) extension headers. Supports IPv4 header options, TCP header options, and TCP, ICMP and UDP data as well, input from either: keyboard as UTF-8/ASCII, keyboard as hexadecimal, or from file. All values within ethernet frame can be modified arbitrarily. Packet crafting and sending one, multiple, or flooding IPv4 and IPv6 packets of type TCP, ICMP, or UDP (or cycle through all three). Written in C on Linux with GUI built using GTK+ and released under GPLv3. Supports IPv4, IPv6 including extension headers, and tunneling IPv6 over IPv4.
0 Comments
Leave a Reply. |